MM Fitting Rings

For the gearheads in the audience
queenandrock
Posts: 2
Joined: Fri Mar 08, 2013 2:02 am

MM Fitting Rings

Post by queenandrock »

Hello,

I have the fitting rings from MM. My KH will be ordering a locking cock ring first, and then after some time she will get a cage for it. I think her plan is to alternate between the cock ring and the cage, but always keeping one of them locked on. I'm trying to determine which base ring to use. I've switched back and forth between the largest and next to largest of the plastic fitting rings.

Largest ring: Comfortable, worn for a few days initially. One testicle popped out during my first night while asleep. Seems to hold everything well otherwise.

Next to largest ring: Very tight but tolerable. Testicles and cock stayed in the ring, even over night. A little painful at times during the day, and some chaffing at the top of the base of my cock. Also, some pinching at the base of my testicles, right in the middle.

Also, when fully erect and after maybe an hour of being permitted to fuck my KH with it on, I was incredibly sore at the base of my cock and tried (unsuccessfully) to get it off. I had to wait until my erection relaxed to remove it. This was JUST the base ring.

With both, I did not use any lube or anything else. I wanted to get the worst case scenario feelings.

One interesting note is that after wearing the next to largest ring for a few days, when I switched back to the largest ring, my testicles easily popped out. I'm thinking that the time in the smaller ring actually had a lasting effect on my package.

I am aware the the plastic fitting rings are not designed to be worn. They have a seam on the inside. The metal rings will be much more wearable, but having nothing else to go on, I want to make an informed decision for my KH.

So which should I go with, the largest ring or the next to largest? I'm thinking the largest base ring would be better for long term or even permanent wear. But I don't want to slip out, and may have some real painful issues if the base ring is too tight when I am erect.

Rock
dickinabox
Posts: 6
Joined: Thu Mar 07, 2013 11:55 pm

Re: MM Fitting Rings

Post by dickinabox »

In my limited experience with CB6000S rings, my system got used to the smaller, previously less comfortable base ring over time. Testicles popping out is not acceptable at all. The chaffing can be dealt with by using a little skin lotion under it, and by using rings that have no seam, as you mentioned.
Device owned: CB6000S, MM Jailbird on order
Last release: March 7, 2013
Breed36
Posts: 60
Joined: Wed May 09, 2012 11:28 am

Re: MM Fitting Rings

Post by Breed36 »

I'm not sure your problems with the sizing rings will be the same as they are for whatever device you end up in. The rings are really narrow. Some device base rings are much wider which will change how they fit to some extent. I also found the rings to be a bit more abrasive than say the base ring of a cb6000.

Now having said that ymmv.

I would go as small as possible with that base ring. You really don't want it slipping off. GL.
User avatar
wishful4
Posts: 991
Joined: Sun Oct 31, 2010 7:15 pm
Location: SE USA

Re: MM Fitting Rings

Post by wishful4 »

Without knowing any more information, my opinion is that you would be well served to buy both rings with your device. Start out in the larger base ring and later transition to the smaller one. It is much different wearing the base ring with a cage versus without. It is the correct spacing between the bottom of the cage and the bottom of the base ring that grips your scrotum and holds the device firmly in place. Don't be afraid to use lube if necessary. Only a small amount and only in the area of discomfort. Your skin will eventually get used to the device.
Wishful4
Current Device: DhGate A271
User avatar
Locked by LRC
Posts: 1034
Joined: Tue Jan 18, 2011 1:45 am
Location: Midwest, USA

Re: MM Fitting Rings

Post by Locked by LRC »

I agree with wishful4. Get one of each size ring. I started that way and wore the larger ring for a couple of days. Then I switched to the smaller one during the day only. My body adjusted and now I wear the smaller ring all the time. With the cage or cock ring installed your ball may not come out.
Current device - MM Custom
Previous devices - CB2000, 3000, 6000, 6000s, Curve
User avatar
locked4her55
Posts: 2236
Joined: Sat Feb 25, 2012 10:23 pm
Location: Massachusetts, USA
Gender:

Re: MM Fitting Rings

Post by locked4her55 »

Yup, what they said. :P

Here's a scenario. Let's say you get only one ring now and you find after a week or so it's too big. MM will resize the ring for you for a $10.00 charge but you are now not wearing your device for a week or two. The odds are you will move down in size over time.

Order both rings now. Then, if and when you do move down to the smallest of the two and the larger one just doesn't work anymore you only need to send back the larger one (while still wearing your CD) to make it smaller and maybe add a second ring so you would now have a double base ring. (I love my double)

It's like that Fram Oil Filter ad. Pay me now or pay me later. Chances are good it's going to happen.

Hey, it's only three seasoned MM veterans making a suggestion. 8-)
Happily secured since 4/2010 :-)
Have worn CB3000, CB6000s, MM Jail Bird & Watchful Mistress,
DHgate A271 & 273, DHgate Full Stainless Steel Belt & DHgate HT nub
Currently wearing A273