Goodbye JB. Hello WM?

[jnuts]

Belle has expressed her desire for a WM in the past. I think after tax time we will get one ordered and sell off the JB. I really want a smaller cage. This one doesn't deter an erection much if at all. It just makes is crazy painful. I think as far as measurements go, we will go down at least half a size in diameter and cut the length down to about 1 3/4. That should make things a lot more comfortable. Everything else should be fine. It is only uncomfortable when I'm hard and the base ring digs in.

[Dev]

Remind me again what measurements you have on your JB?

D

[michaelnmelissa]

Jnuts,

Can I ask how long you measured flaccid? And how long your JB is? I measure 2 1/2 and I ordered the WM at 2 1/4. MM said that should be okay. I wonder if I should email him and ask for a 2"?

Michael

[Dev]

Jnuts,

Can I ask how long you measured flaccid? And how long your JB is? I measure 2 1/2 and I ordered the WM at 2 1/4. MM said that should be okay. I wonder if I should email him and ask for a 2"?

Michael

That might be a good idea. Our experience:

CB-6000s was 2 1/2" and Ab didn't fill it. We ordered the JB at 2" and then the WM is 1/4" shorter (1 3/4" length). That has come to be the device/size that Ab prefers.

D

[thumper]

It's worth pointing out that one could obtain a very fine device from Steelworxx for approximately $185-200, including shipping, at today's exchange rates. That compares very favorably to the WM's price of $290, especially when you consider the difference in workmanship. Both costs are for "base" units without any options.

With that shameless plug out of the way, I'll leave you to your deliberations.

[jnuts]

3/8" Gap
2 1/4" Length
1 7/8" Ring -changed to halfway between 1 5/8 and 1 3/4.
1 1/4" Diam

Thumper, can you send me a link to one of those when you get a chance? I have a terrible time with their site on my phone.

[jnuts]

Jnuts,

Can I ask how long you measured flaccid? And how long your JB is? I measure 2 1/2 and I ordered the WM at 2 1/4. MM said that should be okay. I wonder if I should email him and ask for a 2"?

Michael

I would. Even using the shortest measurements over a period of time ended up too long. The weight of the device is to blame I think. Sometimes I almost fill it out but usually only about half.

[thumper]

I just looked at a few to get a handle on price:

http://steelworxx.de/Revenge-31p.html
http://steelworxx.de/Steelheart-28p.html
http://steelworxx.de/Steelheart-2-29p.html

Keep in mind that the prices shown on the site *include* VAT, so make sure you create an account and sign in to see US prices.

[Atone]

when I read your original post I thought it said going down 1/2" in diameter, now I see it says 1/2 a size in diameter. I was wondering how someone could get the measurements that wrong. Somewhere I posted about being careful about going shorter and narrower at the same time. The two dimension interact a bit and the volume of the cage becomes an issue. I think this is more pronounced the more enclosed the cage is. I certainly experienced it with my Pet Trap and had to have it modified (which btw is back and is super cool looking, I have only had time to open the box though, hopefully a test fitting this weekend).

I too am curious about the device thumper is recommending. I love the look of the steelworx devices, the integrated lock in particular. I am just not ready for a full tube just yet.

-A

[jnuts]

It's worth pointing out that one could obtain a very fine device from Steelworxx for approximately $185-200, including shipping, at today's exchange rates. That compares very favorably to the WM's price of $176, especially when you consider the difference in workmanship. Both costs are for "base" units without any options.

With that shameless plug out of the way, I'll leave you to your deliberations.

I just re-read this. $176 for WM? Don't you mean $290?