Ordering a steelworxx Chastity Belt

[bitsy0]

I think I don't understand how to take the measure for the A-Ring. Sometimes i measure 54mm, sometimes 58mm... which looks huge dimensions...

[Atone]

I agree, that does look to be huge.

Which ring on the CB-6000 do you wear? I would start by trying those, I think the largest is 51mm (2").

[bitsy0]

I agree, that does look to be huge.

Which ring on the CB-6000 do you wear? I would start by trying those, I think the largest is 51mm (2").

Yeah, I always wear that (2"). The smaller (47 mm) is painful when I'm excited!

Dietmar has answered me!
He said that he suggest me 38 mm of diameter of the cage (my penis is 38 mm), and 110 m of lenght of the penis... but I think he wanted to say 110 m total length.. cause I said to him that I am 70mm penis and 110 total from base to penis head I think he wanted to say total...
And then he suggested me to choose an A-Ring from 47 to 50.. With the cb i can only use the 50mm, but I heard that plastic is different and more strict... What do you say if I order a 48-49 mm A-Ring?

(I also have a 30$ steel device.. with 2 A-Rings, one of 50mm and one of 45.. all steel. The 45 makes me some pain at the stomach when I am excited, while the 50mm seems to fall down... going down the penis as if it's too loose... do you agree with me If i choose a balanced measure between them? 47 or 48?

[Atone]

I think you are correct in interpreting his response, he usually measures his devices as overall length.

I would recommend getting two A-Rings when you order the device. Two reasons for this, one is that you will almost certainly get it wrong the first time Sorry to break the news but that seems to be the reality. Second is that it is nice to have two rings anyway, sometimes changing rings can relieve discomfort without needing to go without the device. Third, the cost of the second ring up front is about the same as the cost to ship it back and then have him ship it to you and you save the time. Fourth, your body will change over time as you get used to it full time. Crap, that was four reasons, anyway, you get the point.

Based on what you have shared I would get a 50mm (same as you are using now with the CB) and one that is smaller either 47 or 48mm.

I would still spend some time with the overall length. The 38mm diameter sounds reasonable but I would want to be real sure of the 110 overall length, that will be more likely to make an unwanted bulge. If you give it time and that is correct that is what you should get, just be sure. Don't rush it.

[bitsy0]

I thank you for your support, Atone
I think you're right, I should buy a 50mm and an extra 47mm.. (it's +40€ i think)
What do you mean with "unwanted bulge"?
Oh, and, what is RAL-Colouring for people who have allergy? He say that with 40-50€ he can make the device of every RAL colours. What are RAL colours?

[Atone]

What do you mean with "unwanted bulge"?

I'm talking about the increased possibility of it being visible under your clothes. Obviously (I think) the larger the device is the more likely it would be that it may show under some circumstances.

I have no idea on the colors, I think he can powder coat it maybe that is what he is talking about. I personally wouldn't do that unless there was a good reason.

A couple more things for when you order, I would get the comfort ring on the tube. It is not very expensive and it does make a difference. I have had both with and without and I would get it again.

Also, (maybe you mentioned this) I would get the integrated lock, it is really nice and low profile. Even more so with a larger device, one less thing to produce an unusual outline in your pants.

Good luck.

[bitsy0]

But 110mm isn't shorther than the CB? The CB6K's cage is 83mm (130-140mm total from base to penis head)..
Dietmar, in his "measurements guide" shows that the total lenght is a curve-measure (not straight from point to end). Sorry but I don't understand why you say that 110 mm could be big i thought it would be shorter than my CB i'm a bit confused...

You think I could send Dietmar a photo with my penis under a ruler? So that he clearly understand my measurements?

[Atone]

But 110mm isn't shorther than the CB? The CB6K's cage is 83mm (130-140mm total from base to penis head).. Sorry but I don't understand why you say that 110 mm could be big i thought it would be shorter than my CB i'm a bit confused...

I understand the 83mm (3.25in x 25.4 mm/inch = 83mm). Not sure about the 130-140 overall though. It has been a while since I have had my CB3000 out but I would guess the ring and spacer add less than an inch for a total of 108mm. It looks to me like a 110mm long by 38mm tube would be almost the same size as a CB6000. If you haven't had problems with that then you should be fine. I guess I have just become very accustomed to the fact that my steelheart is much smaller than my CB3000. The last time I wore the CB3000 I remember thinking it was rather large.

[bitsy0]

I think exactly the same with the CB.. sometimes I fill it completely, but sometimes not and my penis slip to the top! But you know, I begin thinking that the problem could be the Ring that falls down cause it's too loose... and so the penis cannot fill completely the cage, after a while I wear it.. Just now I'm trying a 45mm of steel!

[Whynot]

Oh, and, what is RAL-Colouring for people who have allergy? He say that with 40-50€ he can make the device of every RAL colours. What are RAL colours?

RAL refers to a standardized set of 127 different colours used in German industry. To get an idea of what they look like have a look here:

http://de.wikipedia.org/wiki/RAL-Farbe

No need to understand German, but you easily see all the different colours and their respective RAL-numbers.

Like Atone said, I would only get a powder coated Steelheart if I had some serious problems with allergies to the ingredients of stainless steel.