Tips on Getting in to Device

[jesselockedup]

I currently have a cb6000. I struggle to get it on as I am highly aroused when putting it on. I am currently in the process of sizing to get a contender which will end up being about 1/2" shorter, how the heck am I going to get it on? Any tips would be highly appreciated. Thanks in advance.

[TwistedMister]

If your problem is that of being aroused when trying to put it on, you need to distract your mind- have everything ready to go (and some lube already applied, to make it a little easier) and then read something that takes your mind off of it. I find that engine repair or computer manuals work very well for this. Keep reading until everything has shrunk to 'normal' size, then quickly get it in place before you can think too much about it. You kind of have to 'sneak up on it' until you get more accustomed to it.

[wolf513]

"Sneak up on it" is exactly the way I refer to it. I used to get everything ready, use a little silicone lube on my member, then play Candy Crush, or some other mentally engaging activity. I'd also use the stocking method described here: https://denyingthumper.com/2014/11/08/t ... ng-method/

It gets easier with time.

[Chastelaxbro]

I do it in the shower. I get it all ready on the side of the tub and begin my shower as usual. As I scrub the body wash on myself, I quickly slide everything on while walking in place. I cannot maintain an erection when walking. I can go from full erection to completely flaccid in 15 seconds guaranteed every time. So, that is my trick.

[all41]

what they said and have a crow bar ready (Q-tip)

[TwistedMister]

Alternatively, you or your other half could put it on immediately after you have had an orgasm and are no longer *able* to become aroused (whatever your refractory period might be).

[warwick]

I have a contender and sometimes I have a little trouble getting my balls through the base ring. does anyone have any good techniques for putting it on.

[jesselockedup]

Warwick, how did you size your base ring? Can you offer any other tips for sizing a contender? I'm working on getting my sizing correct so I can place an order.

[pokekey]

I use the "stocking trick". This is really the sock trick done with woman's stocking because the fabric is thin and stretchy. Best to use the cut off leg of pantyhose or the full leg of a stocking. Knee highs work OK too.

When putting on the base ring I put balls through first. This is counter intuitive but works best. My penis is more squishy - and hurts less when compressed - than my balls. If my penis goes in first then there is not enough room to get the balls through with out some pinching. So pull the scrotum and both balls through first.

Now I put the stocking over my penis. I feed the distal end through the base ring and pull. The fabric makes everything slide along and protects my skin from pinching and abrasion. Unless I have a raging erection I can generally get my penis pulled through with out any fuss.

Next I put the stocking end through the cage and out the end. Again, pull through. This takes a little more finness to get the balance of pulling and pushing the cage. If you push the cage too much the penis bunches up in the end and gets pinched. When I get it right it is easy to suck my penis right into the cage and seat it down on the base ring post. My penis might not be seated perfectly but once it becomes fully flaccid I can get it shifted around. That is easier done on an open design like the Contender than a closed design like the HT.

It is best to use the full leg of the stocking for two reasons. If it is too short you'll find it difficult to keep the stocking on your penis while also threading it through things. Second, the cut end gets frayed. You'll want to trim that back every couple uses. Start with a longer stocking to get more use out of it.

My girlfriend finds this quite easy to do. This has allowed her to get me all put away before she release me from bondage. Now I have no access at all.

[wolf513]

Nice post, pokekey. A couple of additional comments.

When I get it right it is easy to suck my penis right into the cage and seat it down on the base ring post. My penis might not be seated perfectly but once it becomes fully flaccid I can get it shifted around. That is easier done on an open design like the Contender than a closed design like the HT.

I really fill my HTv2 with even a slight erection. I am a grower, so when totally flaccid, I'm normally not long enough to fill the tube, but because the plastic grips the skin a bit, when I get it right with the stocking trick, it sits in there just right. It doesn't slip back during the day. A little silicone lube around the tip keeps things comfy during growth spurts. I find things are most comfortable when the outer skin is pulled up just a bit around the glans (I am circumcised). That keeps me tucked into the tube so that the base ring sits right up against my body.

It is best to use the full leg of the stocking for two reasons. If it is too short you'll find it difficult to keep the stocking on your penis while also threading it through things. Second, the cut end gets frayed. You'll want to trim that back every couple uses. Start with a longer stocking to get more use out of it.

I like to use a full leg and fold it into itself (i.e., double it), and put the fold up against the base. That way the fraying isn't a problem, and you don't get stray threads stuck in the cage.