I've seen wireless estim boxes on Ali, look to be about the size of a keyless entry fob. Ali also has estim equipped cages, anal plugs, sounds, and, probably, nosepickers.
There -is- a wire between control box and electrode, not sure how you'd get rid of that.
HTH
Search found 8 matches
- Mon Sep 13, 2021 4:09 pm
- Forum: Chastity Devices
- Topic: Wireless electro cage
- Replies: 1
- Views: 2251
- Mon Sep 13, 2021 4:03 pm
- Forum: Chastity Devices
- Topic: Imagining a better sheath
- Replies: 2
- Views: 2666
Re: Imagining a better sheath
I'd be more interested in something that was a cross between a sheath and a "bull bag" - start with bag inside out and attached to sheath, slide penis into tube, then invert bag over scrotum, pulling penis between balls and pointing it to rear... Make any sense ? Not sure it's feasible, bu...
- Tue Aug 31, 2021 4:03 pm
- Forum: Chastity Devices
- Topic: 3D printed devices
- Replies: 6
- Views: 5466
Re: 3D printed devices
I was looking at the KB3D designs as well, but many/most of the cages seem to have been dropped from Thingiverse. Any ideas why ?
- Tue May 11, 2021 1:27 pm
- Forum: General Chastity Chat
- Topic: Poppers
- Replies: 8
- Views: 5729
Re: Poppers
One warning - Nitrites(poppers) or Nitroglycerin for angina and ED medications do NOT play well together. They will make your blood pressure head for the floor. NOT A JOKE !
- Mon May 10, 2021 8:14 am
- Forum: Chastity Devices
- Topic: *Closed* Looking for Testers for a New 3D Printed Cage
- Replies: 65
- Views: 55123
Re: Looking for Testers for a New 3D Printed Cage
It looks like you want to use Shapeways to produce this device. I found their "normal" finish too rough and irritating. I understand that a large number of others have the same issue. Sanding is very difficult. The nylon has to be sanded by hand. its low melting point causes it to melt if...
- Wed Apr 14, 2021 10:10 am
- Forum: Chastity Devices
- Topic: Universal headlock?
- Replies: 3
- Views: 5735
Re: Universal headlock?
I seem to remember that Pedro69's KHD cages through shapeways had a slot on the underside of the glans for a thin O ring which would hook over the top of the glans, then run up alongside and fit into the locking block. Don't recall what the diameter of the ring was, probably varied with length of tu...
- Sat May 30, 2015 1:22 pm
- Forum: Chastity Devices
- Topic: Inexpensive devices...
- Replies: 19
- Views: 7991
Re: Inexpensive devices...
I've looked at that one too. I am just not crazy with the 'look' of the cage. It just looks bulky. Ideally I'd like the cage from the 081 and the ring from the 158. Unfortunately they do not attach the same or Id just buy both and try to combine them. I'm going for something as light as feasible. i...
- Mon Sep 29, 2014 5:27 pm
- Forum: Chastity Devices
- Topic: Bending SS on welds ?
- Replies: 12
- Views: 6537
Re: Bending SS on welds ?
with that cage, you are gonna have to think about where the catheter is going to go when you squeeze the rings together. You might not be able to use the catheter at all. If you really want just a shorter cage and are not worried about the catheter (I don't care for them myself), go for it good luck